Under Ground Cable Laying and Pulling Equipment

Manual Type Cable Drum Lifting Jack

Model Number: TISJ-750

Application: For Lifting Cable Drums.
Product Type: Screw type manual cable drum lifting jack.
Ton Capacity: 1 to 10 Ton.
Open Height (Jack in fully open condition): 1050 mm.
Closed Height (Jack in fully closed condition): 750 mm.
Base: 500 x 500 mm Hex.
Material: Mild Steel.

Model Number: TISJ-900

Application: For Lifting Cable Drums.
Product Type: Screw type manual cable drum lifting jack.
Ton Capacity: 1 to 10 Ton.
Open Height (Jack in fully open condition): 1200 mm.
Closed Height (Jack in fully closed condition): 900 mm.
Base: 500 x 500 mm Hex.
Material: Mild Steel.

Hydraulic Type Cable Drum Lifting Jack

Model Number: TIHJ-10

Application: For Lifting Cable Drums.
Product Type: Hydraulic cable drum lifting jack Adjustable type.
Ton Capacity: 1 to 10 Ton.
Minimum Height: 500 mm(Drum Dia. 1000 mm)
Maximum Height: 1300 mm(Drum Dia. 2600 mm)
Hydraulic Bottle Jack Stroke: 150 mm.
Material: Mild steel.

Model Number: TIHJ-20

Application: For Lifting Cable Drums.
Product Type: Hydraulic cable drum lifting jack adjustable type.
Ton Capacity: 1 to 20 Ton.
Minimum Height: 500 mm(Drum Dia. 1000 mm)
Maximum Height: 1300 mm(Drum Dia. 2600 mm)
Hydraulic Bottle Jack Stroke: 150 mm.
Material: Mild steel.

Cable Drum Rotator
TICDR-MD

Application: For Rotating Cable Drums.
Product Type: Cable Drum Rotator adjustable type.
Ton Capacity: 5 Ton.
Minimum Drum Diameter: 500 mm.
Maximum Drum Diameter: 1500 mm.
Material: Mild steel.

Straight Cable Roller Hybrid
TISCR-Hyd

Application: For pulling and laying cables.
Type: floor type or ground roller
Application: for cable pulling and laying.
Roller Material: Nylon x Mild Steel
Surface Finish: Paint Coated
Both side bearings inside the rollers.

Triple Corner Cable Rollers
TITCR- S

Application: For pulling and laying cables.
Type: floor type or ground roller
Material: Mild Steel
Surface Finish: Paint Coated
Both side bearings inside the rollers.

Manhole Cable Rollers
TIMCR-S

Application: For pulling and laying cables.
Type: floor type or ground roller
Material: Mild Steel
Surface Finish: Paint Coated
Both side bearings inside the rollers.

Hanging Type Cable Roller

Type: Hanging or Suspension type roller
Application: for cable pulling and laying.
Frame Material: Mild Steel
Roller Material: P.P. or Nylon
Surface Finish: Paint Coated
Rollers Diameter: 150 mm.
Roller Groove: 92 mm.
Both side bearings inside the rollers.

AB Cable Roller
TIABCR

Type: Hanging or Suspension type roller
Application: for pulling and laying AB Cables.
Frame Material: Mild Steel
Roller Material: P.P. or Nylon
Surface Finish: Paint Coated
Rollers Diameter: 150 mm.
Roller Groove: 92 mm.
Both side bearings inside the rollers.

Earthing Busbar Bending Machine
TIEBM

Type: Hydraulic hand operated
Application: for bending earthing bus bars (Patti).
Bend Up to 150 x 12 mm Bus Bar Or Strips (Patti) Aluminium and Copper & 75 x 12 mm Mild Steel / GI
Material: Mild Steel
Surface Finish: Paint Coated

Swivel Joint
TISWJC

Application: Cable Pulling Swivel connector is suitable for connecting traction wire rope when laying out wire of various specifications, which can release the twisting strength of wire rope.
Capacity: 3 Ton, 5 Ton, 8 Ton, and 10 Ton.
Material: Stainless Steel or Mild Steel.

Single End Cable Socks
TISES

Application: Cable pulling socks provide a protective sheath over cables that facilitate easier installation via ducts, conduits, pipes, or risers. This saves a lot of valuable time and cuts down on cost by facilitating easy installation of standard and multi-fiber cables.
Material: G.I. Wire